Knowing Essential Plumbing Skills is Essential For Installing a Bathtub
Knowing Essential Plumbing Skills is Essential For Installing a Bathtub
Blog Article
How do you really feel in relation to Tools You Need to Install a New Bathtub ?
Installing a bathtub isn't exactly rocket science, but it does need strong plumbing, woodworking, as well as in some cases, tiling skills. Replacing an old tub with a new one is also a reasonably difficult task. If the old tub is readily accessible, the task can move easily; if you need to open up a wall surface to eliminate the old bathtub and position the new tub, the job is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly require an assistant to vacate the old bathtub as well as set in the brand-new one. Make sure you have qualified on your own for the work as well as fit attempting it. As opposed to employing a specialist to take over a halfway-completed project, it is better to think about utilizing one prior to you begin. Chances are you may need a specialist plumber to make tube links.
This article will help you install a new bathtub in your restroom if you have actually already acquired a brand-new tub as well as do not need to alter the arrangement of your previous water supply pipes.
Your devices as well as product list must consist of the following:
Preparing for the Setup
To start with, the sustaining framework supplied with the bathroom needs to be fitted (if called for) according to the supplier's directions. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is necessary to ensure that if the tap features a plastic washer, it is fitted in between the bathroom and the taps. On a plastic bath, it is likewise sensible to fit a supporting plate under the taps device to prevent pressure on the bathtub.
Fit the flexible faucet adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit completion of the flexible overflow pipe to the overflow electrical outlet. Afterwards, screw the pipe to the overflow face which ought to be fitted inside the bathroom. Ensure you utilize all of the provided washing machines.
Link the trap to the bottom of the waste outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bath ought to currently prepare to be fitted in its final setting.
Removing Old Touches
If you require to change old faucets with new ones as a part of your installation, then the first thing you need to do is detach the water supply. After doing so, turn on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be rather bothersome due to the restricted gain access to that is commonly the instance.
Utilize a container wrench (crowsfoot spanner) or a tap device to reverse the nut that links the supply pipelines to the taps. Have a towel all set for the staying water that will come from the pipes. As soon as the supply pipelines have actually been gotten rid of, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from turning during this procedure. When the faucets have been eliminated, the holes in the bath/basin will have to be cleaned up of any type of old sealing substance.
Before carrying on to fit the brand-new taps, contrast the pipe connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Mounting the Bath tub
Making use of both wooden boards under its feet, place the bathtub in the needed setting. The wood boards are useful in equally spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four tiny points.
The next objective is to make certain that the tub is leveled all round. This can be attained by checking the level and also readjusting the feet on the bathtub up until the level reviews degree.
To install faucets, fit all-time low of the furthest flexible faucet connector to the suitable supply pipe by making a compression sign up with; after that do the exact same for the other tap.
Activate the water system and also examine all joints as well as new pipework for leaks and also tighten them if needed. Fill up the bath tub as well as likewise inspect the overflow outlet and the typical electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as described in the supplier's instruction manual. Tiling and sealing around the bath tub must wait till the bathtub has actually been used at the very least once as this will resolve it right into its final position.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic port to avoid damages to the string. One end of the adapter fits on the plastic tail of the tap and the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need decreasing couplers, which connects the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
Next, place the faucet in the mounting hole in the bath/basin ensuring that the washers are in area in between the tap as well as the sink. Secure the tap in position with the maker provided backnut. As soon as the tap is securely in position, the supply pipelines can be attached to the tails of the taps. The faucets can either be attached by utilizing corrugated copper piping or with normal tap ports. The previous kind must be attached to the tap ends initially, tightening up just by hand. The supply pipelines can later on be linked to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the location where the bathroom satisfies the ceramic tile, it is essential to secure the joins with a silicone rubber caulking. This is important as the installation can relocate enough to break a stiff seal, creating the water to penetrate the wall in between the bathroom as well as the tiling, causing problems with moisture and feasible leaks to the ceiling listed below.
You can select from a variety of coloured sealers to blend in your fixtures as well as fittings. They are marketed in tubes as well as cartridges, and also are capable of securing gaps approximately a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to constantly load the bath tub with water before sealing, to enable the activity experienced when the bathtub remains in use. The sealant can break relatively early if you do not think about this motion before sealing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are also conveniently offered on the market. It is recommended to fit the floor tiles utilizing waterproof or waterproof glue and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was made aware of that write-up on Installing A Bathtub from a good friend on our other web property. If you please take a moment to share this post if you liked it. Thank you so much for going through it.
High-quality repairs here. Report this page